Cisco router configuration

program load complete, entry point: 0x80803000, size: 0x1b340 program load complete, entry point: 0x80803000, size: 0x1b340 IOS Image Load Test ___________________ Digitally Signed Release Software program load complete, entry point: 0x81000000, size: 0x2bb1c58 Self decompressing the image : ######################### [OK] Smart Init is enabled smart init is sizing iomem TYPE MEMORY_REQ HWIC Slot 0 0x00200000 HWIC Slot 1 0x00200000 Onboard devices & buffer pools 0x01E8F000 ----------------------------------------------- TOTAL: 0x02E8F000 Rounded IOMEM up to: 48Mb. Using 6 percent iomem. [48Mb/512Mb] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2012 by Cisco Systems, Inc. Compiled Thurs 5-Jan-12 15:41 by pt_team Image text-base: 0x2100F918, data-base: 0x24729040 This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. Cisco CISCO1941/K9 (revision 1.0) with 491520K/32768K bytes of memory. Processor board ID FTX152400KS 4 FastEthernet interface(s) 2 Gigabit Ethernet interfaces DRAM configuration is 64 bits wide with parity disabled. 255K bytes of non-volatile configuration memory. 249856K bytes of ATA System CompactFlash 0 (Read/Write) Press RETURN to get started! %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up R1>return Translating "return"...domain server (255.255.255.255) % Unknown command or computer name, or unable to find computer address R1>enable R1#con R1#confi R1#configure Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interfa R1(config)#interface giga R1(config)#interface gigabitEthernet 0/0 R1(config-if)#ip R1(config-if)#ip add R1(config-if)#ip address 192.168.1.10 255.255.255.252 R1(config-if)#clo R1(config-if)#clock ^ % Invalid input detected at '^' marker. R1(config-if)#clock rate ^ % Invalid input detected at '^' marker. R1(config-if)#clock rate 128000 ^ % Invalid input detected at '^' marker. R1(config-if)#? arp Set arp type (arpa, probe, snap) or timeout bandwidth Set bandwidth informational parameter cdp CDP interface subcommands channel-group Add this interface to an Etherchannel group crypto Encryption/Decryption commands custom-queue-list Assign a custom queue list to an interface delay Specify interface throughput delay description Interface specific description duplex Configure duplex operation. exit Exit from interface configuration mode fair-queue Enable Fair Queuing on an Interface hold-queue Set hold queue depth ip Interface Internet Protocol config commands ipv6 IPv6 interface subcommands lldp LLDP interface subcommands mac-address Manually set interface MAC address mtu Set the interface Maximum Transmission Unit (MTU) no Negate a command or set its defaults pppoe pppoe interface subcommands pppoe-client pppoe client priority-group Assign a priority group to an interface service-policy Configure QoS Service Policy R1(config-if)#? arp Set arp type (arpa, probe, snap) or timeout bandwidth Set bandwidth informational parameter cdp CDP interface subcommands channel-group Add this interface to an Etherchannel group crypto Encryption/Decryption commands custom-queue-list Assign a custom queue list to an interface delay Specify interface throughput delay description Interface specific description duplex Configure duplex operation. exit Exit from interface configuration mode fair-queue Enable Fair Queuing on an Interface hold-queue Set hold queue depth ip Interface Internet Protocol config commands ipv6 IPv6 interface subcommands lldp LLDP interface subcommands mac-address Manually set interface MAC address mtu Set the interface Maximum Transmission Unit (MTU) no Negate a command or set its defaults pppoe pppoe interface subcommands pppoe-client pppoe client priority-group Assign a priority group to an interface service-policy Configure QoS Service Policy R1(config-if)#? arp Set arp type (arpa, probe, snap) or timeout bandwidth Set bandwidth informational parameter cdp CDP interface subcommands channel-group Add this interface to an Etherchannel group crypto Encryption/Decryption commands custom-queue-list Assign a custom queue list to an interface delay Specify interface throughput delay description Interface specific description duplex Configure duplex operation. exit Exit from interface configuration mode fair-queue Enable Fair Queuing on an Interface hold-queue Set hold queue depth ip Interface Internet Protocol config commands ipv6 IPv6 interface subcommands lldp LLDP interface subcommands mac-address Manually set interface MAC address mtu Set the interface Maximum Transmission Unit (MTU) no Negate a command or set its defaults pppoe pppoe interface subcommands pppoe-client pppoe client priority-group Assign a priority group to an interface service-policy Configure QoS Service Policy R1(config-if)#clock rate 128000^Z R1# %SYS-5-CONFIG_I: Configured from console by console ^Z R1#^Z R1#^Z R1#^Z R1#^Z R1#con R1#confi R1#configure no shutdown ^ % Invalid input detected at '^' marker. R1# R1# R1# R1# R1# R1#config R1#configure no shutdo R1#configure no shutdown ^ % Invalid input detected at '^' marker. R1#no shut down ^ % Invalid input detected at '^' marker. R1# R1# R1# R1# R1#